FIBERuary Carole Adams


FIBERuary Day 26



Black Walnut nut and leave detail.JPG

Black Walnut trees are found from Canada to Florida.    They are found in forests and in neighborhoods.  The nuts start dropping in late September and sometimes you can smell the tree before you see it  They have a delightful odor.  The nuts are covered with a greenish-brown hull.

I have found that people are always glad for you to pick them and take them away.  They stain cars, clothes and can make a mess of a yard.    If the hulls have turned brown you will need to wear gloves when picking them otherwise your hands will be stained  a pretty brown. If you can’t find a tree near you check on Craig’s list, I have seen ads to come and pick for free

I do not take the walnut out of the husk as the walnut contains tannins which are a mordant helping the dye to adhere to the fiber..

                             PREPARATION AND DYEING

If you are not going to use them for dye right away I suggest you either let them dry out or freeze them.  You can also make up the dye solution and freeze it.   I prefer to let them dry out.  I put them on a  baking rack and let them dry naturally.


They will turn a dark brown when dried.  I then store them in a glass jar for future use.  You can also freeze them.  I always have an ample supply at the ready..  They  can be used many times.  

I fill up my dye pot with water and put my hulls in a cotton cloth.  Tying the ends so the walnuts don’t come out.  (They tend to come apart during the dyeing process and the pieces are hard to take out of wool.)  I bring this to a simmer.  You will notice the color of the water changing almost immediately after you put the nuts in.   I let the water simmer for an hour or so  Then I remove the cloth with the nuts in it and let it drain.  You will find you have a wonderfully colored cloth


.  I let the water cool before adding wet wool, slowly bring it up to a simmer again and after 30-45 minutes bring out your wool. .  This dye will work on all sorts of natural fibers.

The picture below is  of cotton and wool fabric and wool roving.  It was left in less than a half hour.  If left in the dye pot longer the color will deepen .  Adding more hulls to the water will also make the dye darker.



I like to over dye plaids with this dye as it give the plaids a primitive look.  


This dye can also be used to dye and over dye embroidery thread.


I am going to put it back in the dye pot in hope to get a little darker color.


Below is some roving dyed with the copper solution


Enjoy Natural Dyeing

Carole Adams   Whispering Pines Frm





FIBERuary Day 14    Copper Dye Recipe    Carole Adams


For all you dyers out there this is a simple recipe for making a wonderful blue dye.  The color of blue will vary depending on your water source.  All fibers seem to take this dye.


Copper tubing, wire or lots of copper pennies (I used copper pipe from a plumbing job)

Gallon Glass Jar with Lid (a pickle jar is good)

1 Quart clean ammonia ( NOT SUDSY)

3 Quarts water


Place the copper into the gallon jar, pour in the 1 quart of ammonia and the 3 quarts of water.   Cover and let stand for 1 week or so until the color turns from a light blue to a deep royal blue.  Now it’s ready to use. Drop a handful of wet, clean fleece, yarn, silk or cotton in.  You don’t need to stir it but don’t let it sit on top.  Take it out within 15 minutes, If you want it darker you may put it back in .  Leaving the fiber in for longer than 30 minutes may cause damage to the fiber.  This dye can be used for approximately 8 months then new ammonia can be added.    I think its best to make a new solution.  Colors will vary from blue-green to a deep royal blue depending on your water source.

Have fun.  I would love to have you send me pictures of your dyed fiber    Carole